Whirlpool washer error codes indicate specific issues such as door lock failures, motor problems, low water flow, drainage faults, excessive suds, and control system errors. Understanding these codes helps you diagnose problems faster and apply the correct troubleshooting steps.
Complete List of Whirlpool Washer Error Codes
Whirlpool washers use diagnostic error codes to help identify problems with drainage, water supply, lid locks, motors, sensors, and electronic controls. Understanding these codes can help you troubleshoot your washer more efficiently and determine whether a simple fix or a replacement part is needed.
- F0E1 (RL) – Load Detected During Clean Washer Cycle
- F0E2 – Excessive Suds
- F0E3 – Overload Condition
- F1E1 – Main Control Board Error
- F1E2 – Motor Control Error
- F2E1 – Stuck Button Error
- F2E2 – User Interface Error
- F3E1 – Pressure Sensor Fault
- F3E2 – Water Level Sensor Error
- F3E3 – Air Trap or Pressure System Fault
- F3E5 – Temperature Sensor Error
- F5E1 – Lid Switch Error
- F5E2 – Lid Lock Error
- F5E3 – Lid Unlock Error
- F5E4 – Lid Not Opened Between Cycles
- F6E1 – Communication Error
- F7E1 – Motor Speed Sensing Error
- F7E2 – Motor Drive Error
- F7E3 – Motor Circuit Fault
- F7E5 – Shifter Fault
- F7E6 – Motor Fault
- F7E7 – Motor Unable to Reach Target Speed
- F7E9 – Locked Rotor Error
- F8E1 (LF) – Long Fill Error
- F8E2 – Dispenser System Error
- F8E3 – Overflow Condition
- F8E5 – Water Temperature Error
- F9E1 – Long Drain Error
- F9E2 – Drain Pump System Error
- Sd / Sud – Excess Suds Detected
- LF – Long Fill
- LD – Long Drain
- LOC / LC – Control Lock Activated
- dET – Detergent Cartridge Not Detected
- Err – General Error
F0E1 (RL) – Load Detected During Clean Washer Cycle
The F0E1 error code appears when clothing or other items are detected during the Clean Washer cycle. This maintenance cycle should only be run with an empty drum. Remove all items from the washer and restart the cleaning cycle. Read more: How to Fix the F0E1 (RL) Whirlpool Washer Error Code
F0E2 – Excessive Suds
The F0E2 error indicates that excessive suds have been detected inside the washer. This commonly occurs when too much detergent is used or when non-HE detergent is used in a high-efficiency washer. Reducing detergent usage often resolves the problem. Learn more: Whirlpool Washer Error Code F0E2
F0E3 – Overload Condition
The F0E3 error code means the washer has detected an overloaded drum. Excessive weight can prevent proper washing, spinning, and draining. Removing some items and redistributing the load may help clear the error. Read more…
F1E1 – Main Control Board Error
The F1E1 error points to a failure within the washer’s main electronic control board. The control board manages all major washer functions and may require replacement if the error persists after a reset. Read more…
F1E2 – Motor Control Error
This error indicates a communication or operational problem involving the motor control system. Wiring issues, motor failures, or a defective control board may trigger the F1E2 code. Read more…
F2E1 – Stuck Button Error
The F2E1 error occurs when a button on the control panel remains pressed for an extended period. Inspect the user interface for stuck or damaged buttons and clean the control panel if necessary. Read more…
F2E2 – User Interface Error
The F2E2 code indicates a communication problem between the user interface and the main control board. Loose wiring connections or a defective control panel may be responsible. Read more…
F3E1 – Pressure Sensor Fault
The F3E1 error means the washer cannot accurately determine the water level inside the tub. Common causes include a faulty pressure sensor, blocked pressure hose, or control board malfunction.
Learn how to diagnose and fix the Whirlpool Washer F3E1 Error Code. This complete guide covers common causes, pressure sensor troubleshooting, repair steps, and solutions to restore proper washer operation.
F3E2 – Water Level Sensor Error
This code indicates an abnormal water level reading. Inspect the pressure sensor system and related hoses for blockages, damage, or loose connections.
Learn how to diagnose and fix the Whirlpool Washer F3E2 Error Code, including common causes such as pressure sensor faults, clogged hoses, and incorrect water level readings.
F3E3 – Air Trap or Pressure System Fault
The F3E3 error suggests a problem with the washer’s pressure monitoring system. Debris inside the pressure hose or air trap can interfere with accurate water level detection.
F3E5 – Temperature Sensor Error
The F3E5 error code indicates a malfunctioning temperature sensor. The washer may be unable to monitor incoming water temperatures correctly, affecting wash performance.
F5E1 – Lid Switch Error
The F5E1 code appears when the washer cannot verify that the lid is properly closed. Check the lid switch assembly, lid strike, and wiring connections for damage.
F5E2 – Lid Lock Error
The F5E2 error is one of the most common Whirlpool washer codes. It indicates that the lid lock mechanism failed to lock or unlock properly during operation. Read More: Whirlpool Washer Error Code F5 E2 Repair Guide
F5E3 – Lid Unlock Error
The washer displays F5E3 when it cannot confirm that the lid has unlocked. A defective lid lock assembly or wiring issue is often responsible.
F5E4 – Lid Not Opened Between Cycles
This error occurs when the control expects the lid to be opened between completed cycles but does not detect the action. Opening and closing the lid may clear the code.
F6E1 – Communication Error
The F6E1 code indicates a communication failure between electronic components inside the washer. Wiring harness problems or failed control boards are common causes.
F7E1 – Motor Speed Sensing Error
The F7E1 error occurs when the washer cannot accurately detect motor or basket speed. This problem may involve the motor, shift actuator, capacitor, or control board. Read more: How to Fix Whirlpool Front Load Washer Error Code F7 E1
F7E2 – Motor Drive Error
This code indicates the drive motor is not operating as expected. Faulty motor windings, damaged wiring, or motor control failures may trigger the error.
F7E3 – Motor Circuit Fault
The F7E3 error points to an electrical problem within the motor circuit. Thorough inspection of the wiring and motor components is usually required.
F7E5 – Shifter Fault
The washer’s shift actuator is responsible for switching between agitation and spin modes. A failed actuator or position sensor may generate the F7E5 error.
F7E6 – Motor Fault
The F7E6 error indicates the drive motor is unable to function correctly. Overheating, worn components, or electrical failures may be responsible.
F7E7 – Motor Unable to Reach Target Speed
This code appears when the motor cannot achieve the commanded speed. Overloading, motor wear, or drive system problems are common causes.
F7E9 – Locked Rotor Error
The F7E9 error indicates that the motor or wash basket cannot rotate freely. Obstructions, seized bearings, or motor failures may be preventing movement.
F8E1 (LF) – Long Fill Error
The LF or F8E1 error means the washer is taking too long to fill with water. Check water supply valves, inlet screens, hoses, and household water pressure. Read more…
F8E2 – Dispenser System Error
This error involves the detergent or fabric softener dispensing system. Blockages or mechanical failures within the dispenser assembly may be present.
F8E3 – Overflow Condition
The F8E3 code indicates excessive water has entered the washer. A faulty inlet valve or pressure sensor may be allowing overfilling.
F8E5 – Water Temperature Error
This error occurs when the washer detects abnormal water temperature conditions. Verify that hot and cold supply hoses are connected correctly.
F9E1 – Long Drain Error
The F9E1 error is one of the most frequently reported Whirlpool washer faults. It indicates that the washer is taking too long to drain water, often due to clogged filters, blocked hoses, or a failing drain pump. Read more: Whirlpool Washer Error Code F9E1 – Long Drain Error
F9E2 – Drain Pump System Error
The F9E2 code specifically points to a problem within the drain pump system. Inspect the pump, filter, and drainage path for restrictions or failures.
Learn more about the fix here: Whirlpool Washer F9E2 Error – Drain Pump System Guide
Sd / Sud – Excess Suds Detected
The Sd or Sud error indicates excessive detergent foam inside the washer. Using HE detergent and following dosage recommendations can help prevent this issue. Read more…
LF – Long Fill
The LF code is a water supply error that occurs when the washer cannot fill within the expected time. Water pressure, inlet valves, and supply hoses should be inspected.
LD – Long Drain
The LD error means the washer cannot remove water quickly enough. Drain pump restrictions and clogged hoses are common causes.
LOC / LC – Control Lock Activated
The LOC or LC code indicates that the control lock feature has been activated. Disabling the lock function restores normal operation of the control panel.
dET – Detergent Cartridge Not Detected
The dET code appears when the washer cannot detect the detergent cartridge. Ensure the cartridge is installed correctly and compatible with the washer. Read more: How to Fix dET Error Code – Whirlpool Front Load Washer
Err – General Error
The Err code is a general fault indication that may require additional diagnostics. Restarting the washer and checking for secondary error codes can help narrow down the cause.
Whirlpool washer error codes help identify problems with drainage, water supply, lid locks, motors, sensors, and electronic controls. Understanding these codes can make troubleshooting faster and help you determine whether the issue requires simple maintenance, a replacement part, or professional repair.
Affiliate Disclosure: This page may contain affiliate links. If you make a purchase through these links, we may earn a small commission at no extra cost to you. This helps support our free washer repair and troubleshooting guides.